twigflat8

How to Replace a Kia Sportage Replacement Key The key of a lot of Kia models has the keyless entry feature built into. This key usually resembles an electronic remote and can be changed with a brand new one from a Kia dealer or locksmith. Key fobs can fail to function due to a number of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how you can get your Kia Sportage replacement key back to working. How to replace a remote key or a smartkey? The battery in your Kia's intelligent key will eventually require to be replaced, regardless of whether it's a remote that starts with a push button or a standard metal key that doesn't have an electronic transponder. This is particularly relevant if your vehicle displays a message that indicates that the smart key or remote has a low battery. It's a simple procedure. In order to replace the battery in the key fob remove the mechanical key from the slit at the back of the key fob. Then remove the cover. Inside the key fob, there will be a small screw that holds the battery in its place. By using a small screwdriver unscrew the screw and remove the old battery. Insert the new battery and close the slit on the key fob. Test the key fob by pressing the lock/unlock buttons. You're good to go If the doors lock and unlock as you expect. You can now utilize Kia's hands-free lock/unlock function whenever your fingers get chilly or you need to go on errands around Brandon. Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a particular programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key has to be reprogrammed, you must be aware of the number printed on the tag of the key code and save it in a safe place. How to replace the battery If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery needs to be replaced. A low battery may also cause other issues, such as the check engine light coming on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires just a few basic tools. Before you begin, make sure that your vehicle is off and all doors are shut. Find the small metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the metal key comes out. Then, you can insert the key into the door handle of the driver to open your car. To replace the key fob battery, remove the rear cover and use a pry bar tool to remove the latch that holds the black negative battery cable. Remove the old battery and then orient the new one so that the “+” positive side is facing you, while the “negative” negative side is facing towards the fob's electrical contacts made of metal. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts. After the new battery has been installed then turn the key fob off and then on in the ignition for a few times until the door locks cycle. You can then test your Kia key fob to check whether it's functioning properly again. How to replace the smart key? Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key features an embedded mechanical key blade, while the standard key fob does not. Both types of key fobs are equipped with batteries inside that will eventually have to be replaced. This is a straightforward process which takes just two minutes. Before you start it is important to ensure that you're on a level surface with sufficient lighting and that your Kia is off. Keep in mind that the fob has small pieces that could fall when you're not careful. The release button for the small size is located on the lower backside. This will be either a circular or rectangular slot. You can open the key fob by pressing the button. After the key fob has been opened, remove the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. After installation it should be possible to lock, unlock and start your vehicle using your key fob even if your engine isn't running! How to replace the mechanical key The Kia key fob is an amazing convenience that allows us to lock and unlock our vehicle with the push of a button. Like kia picanto key fob replacement , the Kia key fob can occasionally have problems. There are ways to address these issues and keep your key fobs functioning for the duration of. One of the most common problems is a low or dead battery. This could cause your device to stop working or work intermittently. If this is the problem, replace the battery with a new one. If this isn't enough to solve the issue, use a standard flathead screwdriver to push the fob's plastic casing open. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one. When the new battery is in, close and then open the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit into the slot). Test the fob to make sure it's functioning correctly. Contact a dealer, or a locksmith to fix the issue in the event that the key fob is not working. Make sure they make you an emergency key that functions for all trunk and door cylinders to prevent lockouts in the future.